Skip to main content
Version: 1.2.2

PPE (Personal Protective Equipment)

PPE

The personal protective equipment, or PPE detection triggers an alarm if the person(s) detected are not wearing either a protective helmet, a visibility vest, or both.

  • Core technology: full body detection.
  • A camera with a minimum of 4 FPS is required.
  • Compatible with fixed, PTZ, and thermal cameras.
  • Areas of interest can be defined.
  • Send data to third-party software.

A single alarm tracking both vest and helmet on 4 people takes up 17% and 2,4% of the analysis slots on Jetson NX and x86-64 machines, respectively. See the table below for detailed resource usage or read on to learn more about resource usage in general.

New PPE

  1. Select PPE by clicking on its box. Fill in the form, as follows:

  2. Name: A readable name of this alarm. This name will appear in the Events view and in all notifications.

  3. Armed: The alarm can be deactivated here. Armed by default.

  4. Schedule (optional): You can associate one of your previously defined Schedules with this alarm.

  5. Cooldown (seconds): After an alarm is triggered, it won't be triggered again for the specified duration. Minimum value is 5 seconds.

    Note that cooldown is applied individually, for each tracked object - if a new, untracked object enters the area, analysis will always occur regardless of the time set here (therefore no detections will be missed).

  6. Add Camera: Select a camera from the list.

NOTE: Cameras below 6 FPS will not show up on the list of cameras for PPE!

Add Camera to Alarm
  • Draw Areas (ROI) (optional): Sometimes the alarm should be limited to a specific area of the video. If you would like to observe only a specific area, it can be determined here. Clicking this button makes the Camera Editor appear. Without ROI, the entire area will be observed.
Detection Size Settings
  • Set object size (optional): If you have a good idea of what pixel range the detected objects would fall into, you can customise the minimum and maximum height size of detections, in pixels, here. This would ensure that only objects that fit into that range would get detected, resulting in a further decrease in the number of false alarms.

    Move the the arrows by clicking and dragging them to help you determine the optimal values. Adjust the slider's endpoints on the bottom part of the screen to set the minimum / maximum values. Click Set sizes to save your changes, or Discard to cancel them.

    NOTE: Take care that any object below or above the set range will NOT be detected, possibly resulting in missing incidents. It is good practice to set the minimum size slightly below, and the maximum size slightly above the desired amount.

    For example: If using Ultinous AI Suite with a combination of radar and PTZ cameras, setting custom object sizes would result in detections only if the radar have detected movement - since setting the proper minimum size would rule out random noise causing false detections.

  • Sensitivity: The sensitivity of the detector can be fine tuned here. Lowering the sensitivity causes less false detections but decreases accuracy. Increasing it results in more alarms but may cause more false detections as well. The default sensitivity is Medium.

  • Selected personal protective equipment: Choose one or both types of PPE to trigger alarms if the person(s) detected are not wearing them.

  1. Capacity: The maximum number of people analysed at the same time. Note that the more people the analysis is run on, the more Analysis slots the Solution will use. The default settings are Person limit: 4.

  2. Click the Submit button to save your settings or proceed to Integration.

Integration (optional)

Ultinous AI Suite offers a wide range of possibilities when it comes to integration with third-party services. Follow the links below to read their respective entries in the guide.

  • HTTP webhook (Milestone XProtect or custom solution via alarm API) Enables / disables event sending: Use this feature to send triggered events to a third-party software with an optional snapshot image of the incident attached. Sends a HTTP POST request to the URL set below, with a content type of application/json. Read on to learn about the schema formatting.

    The following information should be provided by the third-party software's administrator:

    • Target URL: The location of the API.
    • Header keys and values: Key and value of custom HTTP header. Click the Add button to add more Keys. To delete a Key, press the Trash icon next to it.
    • Trust all certificates: If enabled, HTTPS certification errors will be ignored.

      NOTE: Custom CA certificates can be uploaded in the Control Panel, under Trusted Certificates.

    • Enable snapshot attach (not applicable to Milestone XProtect): Off by default. If enabled, it fills in the snapshot field of the HTTP message schema in base64 encoded format.
    • Send Test Event: To test your integration, click the Send Test Event button once the HTTP webhook settings are set.

Detailed resource usage

See the table below for detailed PPE resource usage by percentage / solution number limit according to the different chosen configurations.

HardwarePerson limit: 4Person limit: 8Person limit: 16Person limit: 40
Helmet OR VestBothHelmet OR VestBothHelmet OR VestBothHelmet OR VestBoth
Nvidia Jetson NX17% / 517% / 523% / 430% / 330% / 345% / 252% / 189% / 1
x86-642,4% / 412,4% / 413,3% / 304,3% / 234,3% / 236,4% / 157,4% / 1312% / 8